News/Blog

How to Maintain LED Downlights?

Nov. 24, 2020

LED downlight is a lighting fixture that is embedded in the ceiling and emits light. LED downlights are classified as directional lighting fixtures. As long as its opposite side can be adjusted and received, the beam angle is attributed to the condensing light, the light is more convergent, and the brightness is strong. The brighter the illuminated objects, the higher the lumens, and the more set off the quiet atmosphere.

Downlights are generally used in indoor lighting, and the equipment is simple and convenient for people to love. LED downlights to inherit all the benefits of traditional downlights, with low heat generation, long power-saving life, and minimal maintenance costs.


1.How to maintain LED downlights

After buying back the lamps, do not be busy with the equipment, read the symbols of the lamps clearly and read the equipment operation instructions, and then use the equipment and lamps according to the rules of the instructions, otherwise, risks may occur.

Be careful not to change the structure of the lamp during cleaning and maintenance, and do not replace the parts of the lamp at will. After the cleaning and maintenance are completed, the lamp should be installed as it is, and do not miss or wrongly install the lamp parts.

The lamps in the room should be wiped with a dry cloth frequently, and be careful to avoid moisture invasion, to avoid the phenomenon of rust damage or leakage short circuit after a long time; the lamps installed in the toilets and bathrooms must be equipped with moisture-proof lampshades, otherwise, it will greatly shorten the use Life expectancy; lamps installed in the kitchen should be especially careful to prevent oily smoke, because the accumulation of grease will affect the illuminance of the lamp; light-colored lampshades have better light transmittance, but they are simply sticky. Wipe diligently to avoid affecting light penetration Permeability: If the lamp is non-metallic, it can be wiped with a damp cloth to avoid dust accumulation and hinder the lighting effect.

Minimize the number of switches. The principle of lamp switch is to use the sharp rise of filament temperature to speed up the progress. Switching on and off, again and again, will cause the filament to become hot and hot many times. The more frequent will naturally shorten the service life of the filament, so don't switch the lamp too frequently.

When there is a problem, replace the aging light source in time according to the light source parameters supplied by the logo. When replacing the light source, you must pay attention to the key items such as the light source type, interface type, power, and color temperature on the lamp logo. In particular, the light source variety should not be installed by mistake, otherwise, It is extremely easy to cause explosions and other safety accidents (for example, connecting low-voltage light sources to high-voltage lamps) or directly damage light sources and electrical appliances. At the same time, when replacing the light source, please be careful to power off the lamp first, and then replace the light source of the same type and same power after the light source cools down. Generally, the manufacturer of the lamp will have an obvious maximum limit on the light source in the lamp specification book. Value identification, please be careful to select light sources less than or equal to the maximum limit.

Clean up the dust on the lamp surface on time. Statistics show that if the lamp accumulates too much dust, the average annual illuminance will drop by about 30%. Therefore, cleaning up the dust can not only increase the service life of the lamp but also make the lamp illuminance higher.

LED Downlight

2.LED downlight features

Energy-saving: The power consumption of equal brightness is 1/2 of that of general energy-saving lamps.

Environmental protection: It does not contain harmful substances such as mercury and does not pollute the environment.

Economy: The cost of lighting can be recovered in one and a half years due to the reduction in electricity expenses due to electricity saving.

Low carbon: Saving electricity is equivalent to reducing carbon emissions.

Turtle age: LED lamps have a lifespan of 100,000 hours. According to six hours of daily use, one LED lamp can be used for 40 years.

We are Custom LED Downlight Manufacturer. If you are interested in our products, please feel free to contact us.

Contact Us
info@jarstar-tech.com
andy.jarstar-tech
steven.jarstar
+86 183 1881 3129